Sumitomo Electric Hardmetal has extended its range of Flat MultiDrill series (MDF) high-rigidity, coated carbide drills for spot-facing and counter-boring features on horizontal, curved or inclined surfaces.

MDF now includes overall length tools up to 10:1 length-to-diameter ratio, a long shank, external coolant supply (L2D Type) and through-coolant feed (H3D/H5D type) variants.
The MDF series of tools benefit prime applications such as when cross drilling, expanding hole sizes and deep spot facing. With its 180° point angle, true flat bottoming can be achieved; in order to create a seating, for example. Pre-tapped holes can also be produced in thinner plate or sheet material. Now with the up to 10:1 overall length ratio, tools can be used to access component features that are deeper within housings, for instance.
Significant in the series is Sumitomo’s ‘RS’ thinning development, which creates a greater wall thickness at the tip of the drill. Swarf evacuation is effective due to wider pockets that accommodate chips with high orders of flute finishing and a specific shape applied to the rake face. A special high-strength cutting edge helps resist impact damage when features involve interrupted cuts, while also maximising the overall stability of the tool. Due to the design of the tool, minimal burr formation is said to be a further benefit.
The extended line up of MDF drills can be used on general, stainless, alloy and hardened steels up to 50 HRc.
For further information www.sumitomotool.com

Japanese ceramics specialist Kyocera presented a number of new products at the AMB trade fair in Stuttgart last month.

The debutants included the MEAS series for high-speed and high-performance aluminium machining, and the JCT (Jet Coolant Through) series of tool holders with a high-pressure coolant supply.
Milling cutters in the Kyocera MEAS series impress thanks to their long service lives and low cutting forces, says the company. The stable clamping system ensures the form-locking fit of the cutting plate in the plate seat. What’s more, a stable tool-holder design guarantees the durability and reliability of the cutter.
The JCT series of tool holders are optimised for a high-pressure coolant supply. For turning, there is the double clamp JCT variant, which allows a coolant supply from three directions, while for parting-off and external grooving, Kyocera has designed the KGD-JCT variation, which directs the coolant on to the rake and frank surfaces of the indexable insert. The KTN-JCT variation was developed for threading. In this variation, two cooling holes reduce the tendency for plate breakages and therefore facilitate an extension of service life.
In addition, the JCT series includes smaller tools with internal coolant supplies that can operate at a pressure of up to 200 bar. And again there are variations for turning, with screw clamping; these variations have two cooling holes that deliver coolant supply to the cutting edge surfaces of the indexable insert. For external grooving, there is the KGBF-JCT design, which directs the coolant towards the cutting edge of the insert. And for parting-off operations there is the KTKF-JCT variation, which directs the coolant towards the cutting surface from three directions.
For further information www.kyocera.com

Horn has introduced a grooving and parting-off system, 32T, for Swiss-type lathes and smaller fixed-head lathes. With a precision-sintered grooving insert and central clamping screw, the system offers easy insert indexing and direct entry into the seat of the tool carrier.

Importantly, there is no need for clamping elements, which may have a detrimental effect on chip flow. The screw head of the clamping bolt does not introduce interference and therefore permits grooving and parting-off directly at the spindle. Inserts can be used in a neutral position or as left-hand or right-hand configurations.
By adding the new system to complete its triple-edge insert range, Horn is responding to customer solution requests for Swiss-type lathes and other smaller turning machines, in particular for applications where space is at a premium.
The maximum groove depth using 32T is 4 mm with a width of 2 or 2.5 mm. For grooving, the inserts are available with both straight and full radius cutting edges. Horn offers the insert
with a 15° chamfer for parting-off. A cylindrically ground chip-breaker geometry makes for reliable chip removal. The tool carrier is designed as a square shank of 10 x 10 mm or 12 x 12 mm cross section. Each version features internal coolant supply.
For further information www.phorn.co.uk